Circuit Break Podcast #353

The Name Will Arrive

Related Topics
Connector Catalogs

This is the last installment of Stephen's 'Adventures in Injection Molding'. We are going to recap the entire two year sage and close the book on it.

AVRDUDE All The Way Down

The Jeep Prop Fan project rides again! Well some iteration of it at least. Lets design an open source PCM (Power Control Module) for automotive apps!

Illuminati Moment

Is there a statue of limitations on open source hardware projects? This week, Stephen and Parker dive into what open source means for both of them.

Other Resources

Circuit Break Podcast
Webinars
Videos
Tour MacroFab's ITAR-Compliant Facility

November 18, 2022, Episode #353

The quest for the right connector for a project! The right of passage for any hardware electrical engineer starts with a connector catalog.

Jeep Prop Fan Thingy

  • Jeep Prop Fan thingy
  • Spec Sheet
  • Connectors
    • The Quest for 25 Amps
    • TE Connectivity 1-1418362-3
    • Pg 63 of this catalog
  • Haltech released a new PDM
    • 10 8A
    • 4 25A
    • 2 Push Pull

Arduino Opta

  • Arduino’s First Micro PLC
  • supporting standard languages including LD (Ladder Logic Diagram) and FBD (Function Block Diagram)
  • STMicro STM32H747XI dual-core microcontroller
  • Opta Lite, Opta RS485, Opta WiFi
  • High-power relay switching (4 x 2.3 kW)

Manim

About the Hosts

Parker Dillmann
  Parker Dillmann

Parker is an Electrical Engineer with backgrounds in Embedded System Design and Digital Signal Processing. He got his start in 2005 by hacking Nintendo consoles into portable gaming units. The following year he designed and produced an Atari 2600 video mod to allow the Atari to display a crisp, RF fuzz free picture on newer TVs. Over a thousand Atari video mods where produced by Parker from 2006 to 2011 and the mod is still made by other enthusiasts in the Atari community.

In 2006, Parker enrolled at The University of Texas at Austin as a Petroleum Engineer. After realizing electronics was his passion he switched majors in 2007 to Electrical and Computer Engineering. Following his previous background in making the Atari 2600 video mod, Parker decided to take more board layout classes and circuit design classes. Other areas of study include robotics, microcontroller theory and design, FPGA development with VHDL and Verilog, and image and signal processing with DSPs. In 2010, Parker won a Ti sponsored Launchpad programming and design contest that was held by the IEEE CS chapter at the University. Parker graduated with a BS in Electrical and Computer Engineering in the Spring of 2012.

In the Summer of 2012, Parker was hired on as an Electrical Engineer at Dynamic Perception to design and prototype new electronic products. Here, Parker learned about full product development cycles and honed his board layout skills. Seeing the difficulties in managing operations and FCC/CE compliance testing, Parker thought there had to be a better way for small electronic companies to get their product out in customer's hands.

Parker also runs the blog, longhornengineer.com, where he posts his personal projects, technical guides, and appnotes about board layout design and components.

Stephen Kraig
  Stephen Kraig

Stephen Kraig is a component engineer working in the aerospace industry. He has applied his electrical engineering knowledge in a variety of contexts previously, including oil and gas, contract manufacturing, audio electronic repair, and synthesizer design. A graduate of Texas A&M, Stephen has lived his adult life in the Houston, TX, and Denver, CO, areas.

Stephen has never said no to a project. From building guitar amps (starting when he was 17) to designing and building his own CNC table to fine-tuning the mineral composition of the water he uses to brew beer, he thrives on testing, experimentation, and problem-solving. Tune into the podcast to learn more about the wacky stuff Stephen gets up to.

Special thanks to whixr over at Tymkrs for the intro and outro!

Related Podcasts

We are all idiots together on this planet

We Are All Idiots Together On This Planet

What is your EDA Tool workflow? Where do you start with a new design? When is it O.K. to rely on another part footprint? Are JEDEC standards fine?

Connector catalogs

Connector Catalogs

This is the last installment of Stephen's 'Adventures in Injection Molding'. We are going to recap the entire two year sage and close the book on it.

Illuminati moment

Illuminati Moment

Is there a statue of limitations on open source hardware projects? This week, Stephen and Parker dive into what open source means for both of them.

Avoid the extremes

Avoid The Extremes

Controlling PCB costs of your next product is all about avoiding the extremes of the manufacturing specifications. Don't let your EDA tool fool you!

Color clashing chip consolidation

Color Clashing Chip Consolidation

What is the worst thing about the Analog Devices and Linear Technologies merger? The incompatible color schemes of course.

Avrdude all the way down

AVRDUDE All The Way Down

The Jeep Prop Fan project rides again! Well some iteration of it at least. Lets design an open source PCM (Power Control Module) for automotive apps!

About MacroFab

MacroFab offers comprehensive manufacturing solutions, from your smallest prototyping orders to your largest production needs. Our factory network locations are strategically located across North America, ensuring that we have the flexibility to provide capacity when and where you need it most.

Experience the future of EMS manufacturing with our state-of-the-art technology platform and cutting-edge digital supply chain solutions. At MacroFab, we ensure that your electronics are produced faster, more efficiently, and with fewer logistic problems than ever before.

Take advantage of AI-enabled sourcing opportunities and employ expert teams who are connected through a user-friendly technology platform. Discover how streamlined electronics manufacturing can benefit your business by contacting us today.